Custom Medal Reorders: How to Reuse Your Mold and Cut 30% Off the Next Order

View:61518Time:2026.11.15

Every February we get the same email, usually from a race director who ordered from us two years ago: "We need the same medals again, but with 2027 on them." Then a pause in the thread, because they're expecting to be told it's a new project — new tooling, new samples, new three-week approval cycle, and a bill that looks like the first one.

It isn't. Custom medal reorders are the cheapest, fastest order a race or a club will ever place, and most buyers never find out because nobody explains the mechanics. Your die still exists. It's in a rack in our tooling room with your event name on the tag. Reusing it removes the tooling fee, the sample cycle, the artwork approval, and roughly half the production time — which on a 500-piece order is where a 25–30% cost reduction comes from.

This page is the honest version of that, including the part where the 30% shrinks if your order is large. What a reorder is and isn't, what you can change for free, what genuinely requires a new die, what we keep in the archive, six reasons reorders go wrong, and how to design a medal that's still cheap to order in year five.

Table of Contents

The Short Answer: What a Reorder Actually Costs

A reorder uses the die you already paid for. No new tooling, no new sample, no new artwork approval: production runs 7–12 working days instead of 15–20, and total project cost typically drops 25–30% on a 500-piece order. At 2,000 pieces the saving is closer to 8%, because the die was already spread thin.

Cost line First order Reorder
Die / tooling $150–300 (3D), $80–150 (2D) $0 — die on file
Artwork setup & dieline 3–5 days 0–1 day
Sample & approval 7–10 days, $60–120 0–5 days, $0–40 (only if you want a new colour proof)
Production 15–20 working days 7–12 working days
Standard MOQ 50–100 per design 25–50 — the die already exists
Unit price Tier price for the quantity Same tier, or one tier better at the same quantity

What Counts as a Reorder — and What Doesn't

A true reorder means the same die, the same physical size, and the same relief structure. Every element that lives in the steel stays exactly where it was. What changes is everything applied after casting: plating colour, enamel colours, ribbon, engraving, packaging.

Buyers get this wrong in one specific direction. "Same medal, just 5mm bigger" is not a reorder. "Same medal but with the logo moved 3mm left" is not a reorder. "Same medal but as a shield instead of a circle" is not a reorder. Each of those needs a new die, and the tooling cost is the same as if you'd never ordered before. Size and shape are the two things you cannot negotiate after the fact — they're cut into steel.

There's a middle category that trips people up too: adding a small element. Say you want the year as a raised tag under the main relief. That's a separate small die, usually $50–80, and it's the cheapest way to keep a dated design reorderable. We'll come back to it, because it's the single most useful piece of advice on this page.

When we say you can reuse a medal mold, this is exactly what it means: the same steel, the same cavities, the same impression, pressed again. Not a copy of your medal, not a new engraving based on a photo — the original tool, sitting in a rack with your name on the tag.

The Arithmetic: Where the 30% Comes From

Take a real configuration: 76mm round, 3D relief front, soft enamel colour, 25mm ribbon, 500 pieces. First order.

Line item First order (500 pcs) Reorder (500 pcs)
3D die $220 —
Sample + courier $85 —
Medal @ $1.85 $925 $925
Ribbon (25mm, 1-colour print) $180 $180
Total $1,410 $1,105
Per medal $2.82 $2.21

That's 21.6% off the project, and 22% off the effective unit price, before you count the buyer's own time — the artwork review, the sample approval, the two weeks of emails. Add the freight consolidation on a repeat shipment and most clients land in the 25–30% range. If the first order included a new ribbon print setup or a packaging die, the reorder saving is larger still.

Now run the same math at 2,000 pieces.

Line item First order (2,000 pcs) Reorder (2,000 pcs)
3D die $220 —
Sample + courier $85 —
Medal @ $1.45 $2,900 $2,900
Ribbon $620 $620
Total $3,825 $3,520

8% — and the absolute saving is the same $305. This is the part nobody tells you: reorder savings are biggest in percentage terms on small orders, because a $220 die is a rounding error on a 5,000-piece programme and a real line item on a 300-piece one. Which means the events that benefit most from reordering are the ones least likely to ask, because they assume they're too small to have anything on file.

The other thing worth knowing: unit price on a reorder can come in slightly below the first quote at the same quantity. Not because we're being generous, but because the die exists, so we can run the full quantity in one continuous pass instead of splitting the first batch around sample approval. On a 1,000-piece order that's usually $0.03–0.08 off per medal.

What You Can Change Without Paying Tooling Again

This is where reorders earn their reputation. A die defines the metal. Everything else is applied, and applied things are changeable.

Change Tooling cost Notes
Plating colour (gold / silver / bronze / antique) $0 Free, but the colour must be confirmed against a physical chip — screen colours lie on metallics
Enamel colours $0 New colour from Pantone, +$20–40 one-off for a colour match if it's outside our standard range
Ribbon colour and print $0–60 New print layout needs a screen setup; colour change alone is free
Event year, dates, distance $0 Laser engraved on the back or on the ribbon — no die change
Back engraving (names, times, sponsor) $0 Laser, $0.15–0.30 per medal if individually engraved
Packaging card, box, bag $0–120 Printed card is a print setup, not a medal setup
Ribbon width $0 As long as the jump ring position still balances the medal
Finish (soft enamel → UV print on the same cavities) $0 Technically possible; says "printed" rather than "enamelled" to the eye

The practical version of that table: a club can run the same die for five seasons and produce five visibly different medals — gold for champions, silver for runners-up, bronze for participation, new enamel colours matching each season's kit, a new ribbon each year, and the year laser-engraved on the back. One die. Five medal programmes. This is how the clubs that order from us every season keep their per-unit cost flat while everyone else's climbs.

What Requires a New Die

Steel doesn't negotiate. These are the changes that mean new tooling, at roughly the prices below.

  • Diameter or overall size — new die, $150–300 for 3D. Even 3mm is a new die.
  • Outline or shape — new die, plus a new cutting path, $150–400 depending on complexity.
  • Relief height or depth — new die. A 1.5mm relief and a 3mm relief are different engravings.
  • Adding cut-outs — new die, $200–400, because the steel has to be machined away and the part flow changes.
  • Adding a moving element (spinner, slider, hinged plate) — new die plus a sub-assembly, $250–400 for the rotating insert alone.
  • Moving a raised element — new die. This one hurts because it looks trivial on a PDF and isn't.
  • Changing the jump ring position — usually a modification to the existing die, $40–80, sometimes free if it's a drilling change.

The cheap exception, and the one worth designing around: a separate year tag. A small struck plate, 18–25mm, that hangs from the main ring or sits in a recess. Tooling is $50–80, it can be re-cut every season for $50, and it lets a die with no date on it carry a year. If your event wants the year visible and you don't want to pay for a die every year, this is the answer.

Design It to Age: The Reorder-Friendly Brief

Whether your medal is cheap to reorder in three years is decided in the first week of design. Here's what we ask clients to lock down before we cut anything.

  1. Decide where the year lives. In the die, on a separate tag, engraved on the back, or on the ribbon. All four work. Only the first costs you $150–300 a year.
  2. Keep the event name generic enough to survive a rebrand. "Springfield Marathon" ages well. A tagline tied to a sponsor who leaves doesn't.
  3. Design the colour layers separately. If the enamel layout is built so colour 2 can become colour 5 without touching the metal, you get a new look for free.
  4. Record the plating reference. Not "gold" — the actual chip code. This is the number that keeps year four matching year one.
  5. Leave 8mm of clear back surface. Enough for a laser-engraved winner name, time, or new sponsor without redesigning anything.
  6. Don't fill the back with a second full design. It looks impressive once and blocks every future change.
  7. Standardise the ribbon width across the series so ribbon stock carries over between seasons.
  8. Approve and keep a golden sample. Physically. In a drawer, not in a photo album.
  9. Ask for the die to stay with the factory and get it in writing, with the archive list.
  10. Photograph the approved sample next to a ruler on delivery day. It takes 30 seconds and settles every future argument about colour.

On point one, an honest trade-off, because the answer depends on volume. If your annual medal spend is above roughly $6,000, put the year in the die — a $220 tooling charge is 3–4% of the order and nobody notices, while a big date in the relief is a design statement runners actually photograph. Below $6,000, the die is 8–15% of your order and paying it every year is just a tax on being small. Use the tag or the engraving. Both are honest; only one is expensive.

What We Keep in the Die Archive

"We keep your mold" is a sentence that sounds reassuring and means nothing until you ask what's actually stored. A die on a shelf is not a reorder system. Real medal mold storage means the steel plus the eight things that make it usable three years later, and this is what goes into the archive for every design we produce.

Item Why it matters on a reorder
Production die + working mold The thing that makes the reorder possible at all
Golden sample, signed and dated The only real defence against colour drift three years later
Plating record (bath type, chip code, thickness) "Gold" is 14 different colours; the code is one
Enamel colour formulas Mixed colours don't survive in anyone's memory
Vector artwork, layered Needed the moment you change a colour or add engraving
Ribbon spec (width, weave, print method, PMS) Prevents the ribbon in year three being a slightly different blue
Packaging spec and print file Card, bag, box — all reprintable without new design work
QC photos from the production run Shows what shipped, not what was approved
Order history with quantities and dates Lets us quote the same tier instantly and predict your lead time

We hold dies free of charge and have never charged a client to retrieve one. If a client skips two or three years, the die is still there; we've pulled dies that were cut in 2014 for a 2026 order and they ran fine. Ask any supplier what their archive includes and how long they hold it. If the answer is "we keep the mold," ask what else. That question separates a factory with a system from a factory with a shelf.

Why Reorders Go Wrong: 6 Failure Modes

Reorders are simple, which makes the failures embarrassing. All six of these have happened to real buyers, most of them not our clients, and all of them are preventable before the first order ships.

1. The die belonged to the previous supplier

Most common by a wide margin. The buyer changes suppliers to save 15% and discovers the die was never theirs — it stays with the factory that cut it. Confirm ownership in writing on the first order. Some factories will hand over the die; most will charge for it; a few will simply refuse. Ask before you need it.

2. No golden sample was kept

Year one is a deep gold. Year three is a paler gold, because the plating bath was refreshed differently, and there's nothing to compare against except a phone photo taken under office lighting. Keep the physical sample. It costs nothing and it's the only reliable reference.

3. Ribbon dye lot drift

Fabric is dyed in lots. A 500m ribbon run in 2026 and a 500m run in 2028 will be close, not identical, and side by side the difference is visible — which matters if last year's medals appear in this year's photos. Order ribbon with 10–15% spare on the first run if consistency across years is important.

4. Different plating bath, different result

Two factories both offering "antique gold" produce two different colours. Even the same factory can drift if the bath chemistry is changed. This is why the plating chip code, not the colour name, belongs in your spec sheet.

5. Flattened or lost artwork

The client sends a JPEG of last year's medal, because the designer left and the files went with them. Everything has to be redrawn, and redrawn artwork never matches exactly. Keep the vector files. Ask for them at delivery, in a folder, in your own storage.

6. Reorder placed on a first-order timeline

The buyer remembers "three weeks" from last time, orders five weeks before the race, and finds out that three weeks was production, not delivery, and that the shipment needs another two. Reorder lead time is short. Reorder planning is the same as it always was.

Failure Prevention, on the first order
Die not yours Written die ownership + archive list in the PO
Colour drift Signed golden sample kept by both parties
Ribbon mismatch +10–15% ribbon overrun; record weave and PMS
Plating drift Plating chip code in the spec, not a colour word
Lost files Receive layered vector artwork at delivery
Late reorder Two dates on the quote: production complete and delivered

7–12 Days Is Production, Not Delivery

A reorder with no changes runs 7–12 working days in production for 500–3,000 pieces. A colour change adds 1–2 days. New back engraving with supplied names adds 2–3 days. Then it has to move.

Stage Reorder timing
Confirm spec against archive (colour, ribbon, engraving) 1–2 days
Production 7–12 working days
QC and packing 1–2 days (inside production)
Express courier to door 3–7 days
Air freight 7–12 days, cheaper above ~100kg
Sea freight 25–35 days, 15–30% cheaper, only for non-urgent top-ups
Realistic door-to-door, express 3–4 weeks

So a reorder needs to be placed four weeks before you need medals in hand, not four weeks before the race — five is comfortable, six is calm. And if the order lands within three weeks of Chinese New Year, add two to three weeks, because the whole supply chain stops and the calendar doesn't care that your race is on. Our production calendar closes about ten days before the holiday and takes a week to come back to full speed.

Ordering More (or Fewer) Than Last Time

Reorder quantities are flexible in both directions once a die exists, and this is the one place where a small event gets real leverage.

  • Down: standard MOQ is 50–100 per design on a first order; on a reorder with a die on file, we'll run 25–50. Below that the setup labour dominates and it stops making sense for anyone.
  • The 50% rule: if you order at least half the original quantity, you usually hold the same price tier. Drop below half and you climb a tier.
  • Up: crossing a tier threshold is worth planning for. At 1,000 pieces the unit drops from the $1.70–2.10 band into the $1.30–1.60 band, so going from 900 to 1,000 can cost less in total than 900.
  • Split colours, one run: if you need 400 gold, 400 silver and 200 bronze, that's one production run with three plating batches, not three orders. Ask for it as one job and the setup is shared.

Five Years on One Die

Here's what it looks like when a race reorders running medals every season for five years — same die, colour and ribbon refreshed each year. Numbers are 1,000 pieces of 76mm soft enamel at our 2026 tier pricing.

Season Quantity Tooling Medals Approx. total
Year 1 1,000 $220 $1,450 $1,670
Year 2 1,000 $0 $1,450 $1,450
Year 3 1,000 $0 $1,450 $1,450
Year 4 1,000 $0 $1,450 $1,450
Year 5 1,000 $0 $1,450 $1,450
Five seasons 5,000 $220 $7,250 $7,470

Compare that with five events re-cutting a die because they changed shape each year: $1,100 in tooling, plus five sample cycles, plus five approval rounds. The difference isn't only money. It's that a matching five-year set becomes a collectible — runners start noticing the series, and the medal stops being a one-day souvenir and becomes a reason to come back. We've watched small races build their whole identity around consistency, and it costs them nothing extra after year one.

When to Re-Cut the Die

Dies wear out. A steel die for zinc alloy casting typically holds its detail for 30,000–50,000 impressions; after that, fine lines soften, sharp edges round slightly, and engraved lettering loses its crispness first. Most events never get near that number. Clubs and large races do.

Signs it's time:

  • Fine lines on the relief look filled-in compared to your golden sample
  • Letter edges are visibly rounded at 100% size
  • Polishing is taking longer per piece, which shows up as a small price increase
  • Plating starts showing more rejects in the recesses, because the surface is rougher

A re-cut costs the same as a first die, $150–300 for 3D. On a 3,000-piece order that's $0.05–0.10 per medal, which is cheaper than the alternative — a batch of medals that looks slightly worse than last year's and gets noticed by exactly the people who care most. If you're ordering 5,000+ a year, plan on a re-cut somewhere in year four to six and put it in the budget.

The Reorder Brief: 8 Lines to Send

You don't need to write a brief. Send these eight lines and we can pull the die and quote the same day.

  1. Event name and the year the original order was placed
  2. Quantity for this reorder
  3. Same plating, or the new plating colour
  4. Same enamel colours, or the new references
  5. Same ribbon, or the new ribbon colour and print
  6. Any engraving: names, times, dates, sponsor lines — with the file or the list
  7. Date you need them in hand, and the address
  8. Anything that was wrong last time and should change

FAQ: Custom Medal Reorders

How long does a medal reorder take?

7–12 working days in production for 500–3,000 pieces, plus 3–7 days express shipping. With no changes at all, we've shipped reorders 11 days after the email. Plan four weeks door-to-door and you'll never be rushed.

Do you charge the mold fee again on a reorder?

No. The die is cut once. You pay tooling on the first order and never again unless you change the size, shape, outline or relief structure — or the die has genuinely worn out after tens of thousands of pieces, which we'll tell you before production, not after.

Can I change the ribbon colour on a reorder?

Yes, and it's the cheapest way to make a reorder look new. Colour changes are free; a new print layout costs $0–60 for a screen setup. Keep the width the same and the medal's balance doesn't change.

Can I switch from soft enamel to hard enamel on the same die?

No, and this is the one upgrade that can't be retrofitted. Hard enamel is polished flat after filling, and polishing wears down the raised metal lines that separate the colours. A die cut for soft enamel has 0.25–0.3mm walls — polishing takes them below the surface and the colours bleed into each other. Going to hard enamel means a new die with 0.4mm walls.

Do you keep my mold if I skip a year?

Yes. We hold dies indefinitely at no charge, including designs from a decade ago. If you come back after five years, we pull the die, check it, and quote a reorder. The only thing that may have changed is the price of zinc and labour.

Can I reorder fewer than the original MOQ?

Yes. With a die on file the practical floor drops to 25–50 pieces. Below that, setup labour makes the per-unit price climb faster than the quantity falls, and we'll tell you when you've crossed that line.

My previous supplier closed. Can you make my medal again?

Usually, if you have a physical sample. We reverse-engineer the die from a scan plus measurements — $150–300 for tooling and about 5–7 extra days — but expect small differences: a re-cut die is a new engraving, not a copy, and 1–2% of fine detail is lost in the process. Send us the sample and we'll tell you honestly whether it's worth doing or whether a fresh design would serve you better.

Pull Your Die From the Rack

If you've ordered medals from us before, send four things: your event name, the year of the original order, the quantity you need, and the date you need them in hand. We'll pull the die, send you a photo of the archive card with the plating and enamel references, and quote the reorder — usually the same day, always within 24 hours. Free colour proofs if you're changing the palette. No tooling charge.

If you've never ordered from us, the same email works, and it's worth reading the first order as a five-year decision: ask for die ownership in writing, ask what goes into the archive, and ask for the golden sample. We do all three as standard. Shenzhen Vistarts Craft Co., Ltd. has been manufacturing event medals in our own factory since 2011 — over 10,000 square meters, 5 production lines, 50+ machines, 150+ employees, 20+ engineers and a 20-person design team working beside the production floor. ISO9001 certified, audited by Disney and Universal Studios, medals supplied for the Paris Olympics, the Qatar World Cup and major marathon events, 1,000+ designs on file, all RoHS and CE compliant — and a full refund if bulk production doesn't match your approved sample.

Send Sean your reorder details:
WhatsApp / Phone: +86 181 2379 9506
Email: sean@vistarts.net
Website: https://www.vistarts.com/

One last thing, from the tooling room rather than the sales desk: the cheapest medal you will ever order is the one whose die already exists, and the difference between a race that has a five-year archive and one that starts from zero every season isn't budget. It's whether anyone asked, on the first order, where the die would live afterwards.

SCIENCE AND TECHNOLOGY ENVIRONMENTAL PROTECTION, REDUCE
ENVIRONMENTAL POLLUTION